Question:what is the correct spark plug gap
Not finding your answer? Try searching the web for
what is the correct spark plug gap
Top Answers
1. Loosen the spark plug from the Craftsman Lawnmower using the spark plug socket and the ratchet. Pull the spark plug from the Craftsman Lawnmower. 2. Tap the top of the small metal arm that is over the top of the small metal pin in the cen...
When you buy spark plugs they sometimes come already gaped for you, but its always better to check the gap. You can get these gap's at the parts store, they will have them up front.
in most cars the spark plug gap can range from 20-65 to make sure ask the parts store when u get them some come already done and some dont, just make sure you get them gaped right or the car wont run right.
More Web Answers
|
If not gapped right your car might start shaking, or even stall or worse no star.
http://wiki.answers.com/Q/What_happens_if_spark_pl...See entire page »
|
|
بسم الله الرحمن الرحيم. هذا الجواب المطلوب لسوالي الذي اتعبني وانا اشكر الرفاق اللذين ساعدوني. If it is a V6, it is .060". hamedalhad@hotmail.com.
http://wiki.answers.com/Q/What_is_the_correct_spar...See entire page »
|
|
.035 non hei..045 with hei.
http://wiki.answers.com/Q/What_is_the_correct_spar...See entire page »
|
|
the plugs are already gapped. On edit: That is not an answer, and you never install plugs without checking the gap. The correct answer is .035".
http://wiki.answers.com/Q/What_is_the_correct_spar...See entire page »
|
|
0.054 for the 1999-2001, others not sure.
http://wiki.answers.com/Q/What_is_the_correct_spar...See entire page »
|
|
.0060.
http://wiki.answers.com/Q/What_is_the_correct_spar...See entire page »
|
|
The correct plug gap for my Toro GTS 6.5 horse mower is 0.035.
http://wiki.answers.com/Q/What_is_the_correct_spar...See entire page »
|
|
0.85mm, but .8 or .9 will do fine also.
http://wiki.answers.com/Q/What_is_the_Correct_gap_...See entire page »
|
|
Answer .044
http://wiki.answers.com/Q/What_is_the_correct_spar...See entire page »
|
|
Answer Example: On a 1992 Lincoln Continental with a 3.8L V-6, if it is still there, look for a decal located normally on the top of the engine fan shroud or stuck under the hood. It will have the engine size, engine family, some EPA/SMOG in...
http://wiki.answers.com/Q/What_is_the_correct_Gap_...See entire page »
|
|
Answer 35 thousands, of an inch, if its a short base plug , 60 thousands, if its a long base plug,
http://wiki.answers.com/Q/What_is_correct_spark_pl...See entire page »
|
|
1. Remove the four screws from the top of the engine cover using a Phillips screwdriver. Lift the engine cover off. 2. Grasp the boot of the spark plug wire and pull the spark plug wire off the spark plug. Remove the spark plug, using the ch...
http://www.ehow.com/how_12227285_correct-spark-plu...See entire page »
|
|
1. Raise the hood of the Accent, and set the hood prop. Locate the spark plug wires, at the front of the engine on the top. 2. Remove one spark plug wire from the spark plug, using your hand to pull the wire boot free with a twisting motion....
http://www.ehow.com/how_8560683_correct-gap-2000-h...See entire page »
|
|
.35 to .40 should be fine also the parts store or a dealer can help
http://www.fixya.com/cars/t2308542-correct_spark_p...See entire page »
|
|
Spark plug gap maladjustment will not stop the engine from starting. It will however produce misfiring or rough idle. More than likely, a spark plug cable has stopped making contact. Check the cables for continuity from the coil end, to the ...
http://www.fixya.com/motorcycles/t3583116-changed_...See entire page »
|
|
1. Grab the spark-plug wire boot. Then twist and pull off the wire from the spark plug. If your vehicle is equipped with Coil on Plug (COP) or Distributorless ignition system, consult your car owner's manual or vehicle service manual to remo...
http://www.ehow.com/how_5079967_measure-spark-plug...See entire page »
|
|
1. Open the box and remove the spark plug. Obtain the proper spark gap for your car either from the owner’s manual or off the emissions sticker on the radiator support under the hood. 2. Select the proper blade thicknesses from a feeler gaug...
http://www.ehow.com/how_6934055_properly-gap-spark...See entire page »
|