Frequently Asked Questions
The 2.4L engine found in some 1996 Toyota Tacomas uses a mass air flow meter mounted inline between the air filter and the throttle body on the engine. This meter (also called the ...
http://www.ehow.com/how_7646491_do-1996-24-toyota-...
The arrangement is the common four-in-line cylinder engine. number one is in the front and the firing order on the dist cap is 1-3-4-2
http://wiki.answers.com/Q/What_is_the_cylinder_arr...
Answer Follow your upper radiator hose between your valve cover and intake manifold. It's right there secured by two 10mm bolts.
http://wiki.answers.com/Q/Where_is_the_location_of...
Hi lux 1977-1996 engine code 2L Torque settings stage 1. 38 newton metres stage 2. 78 newton metres stage 3. +90 degrees stage 4. +90 degrees Sequence . 12 4 6 14 . 18 10 2 8 16 . ...
http://wiki.answers.com/Q/What_are_the_head_bolt_t...
gap? The gap should be pre set when bought, mine are but check with the sales person. 1991 22RE 2.4= The gap is 0.035 but if you are installing fine tip platinum or Iridiums use pl...
http://wiki.answers.com/Q/What_is_the_proper_spark...
Just tighten it you don,t need a spec for valve covers just not to tight just be dillegent and you will be fine
http://wiki.answers.com/Q/What_is_the_torque_specs...
Answer If the engine has a timing belt, it should be changed around the 150K mark. If there is a timing chain, it does not have to be changed unless it is damaged.
http://wiki.answers.com/Q/How_often_do_you_have_to...
the Toyota's I've seen all have electric fuel pumps mounted in the fuel tanks. access is under the back seat.
http://wiki.answers.com/Q/Where_is_the_fuel_pump_a...
Remove it, and throttle body carbon cleaner. Make sure that the valve can be moved easily.
http://wiki.answers.com/Q/How_do_you_clean_EGR_val...
Answer Remove the number one spark plug and take a screw driver and put it in the hole. have someone "bump" the starter (barely try to crank) until you feel the screw driver come u...
http://wiki.answers.com/Q/How_do_you_set_the_timin...
There are two ways to get the clearance required to remove the oil pan. Start by draining the oil pan, after all the oil is out remove the 16 bolts and two nuts holding the oil pan...
http://wiki.answers.com/Q/How_can_remove_oil_pan_1...
Answer You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
http://wiki.answers.com/Q/How_do_you_replace_the_w...
Answer a serp belt tool with a 19mm or similar tool setup will be necessary. remove the splash shield on the right front, reach up from the bottom and attach the socket to the alum...
http://wiki.answers.com/Q/How_do_you_release_the_b...
Answer A standard measure of oil pressure is 10lbs per 1000 RPM. If you have low oil pressure, check to make sure the wire to the sender is connected and clean. I would also replac...
http://wiki.answers.com/Q/What_is_the_Oil_pressure...
I have the same car and I let Jiffy lube do it. It only costs about $15 to learn that they had to use a little effort and it took two people with 4 hands. 2 to hold, 2 to change. Y...
http://wiki.answers.com/Q/How_do_you_release_the_b...
Answer Since there isn't just one ratio available for each model it's tough to say. Inside your driver's doorjam there's a tag with a bunch of information on it. It contains codes ...
http://wiki.answers.com/Q/What_is_the_gear_ratio_f...
torque 39 nm (29 ft-lb) then 90 degrees then another 90 degrees 2 small bolts at front 21 nm (15 ft-lb)
http://wiki.answers.com/Q/What_is_the_head_bolt_to...