WAP54G FAQ

how to configure a wap54g?
1. Hold the reset button located on the back of your WAP54G for 30 seconds. You may need to use the tip of a pen or paperclip to press the button. The green button for the ACT will...
how to disassemble wap54g?
1. Disconnect the AC power cable from its socket on the back of the router. Unplug all networking cables from the device as well. 2. Place the router with the topside facing downwa...
how to access a wap54g?
1. Ensure that the computer is connected to the wireless router. If the computer is connected with an Ethernet cable, the "Link" light on the front of the router should be flashing...
how to unbrick a wap54g?
1. Pick up the WAP54G router and locate the "reset" button. It will be on the left of the back panel and labeled "Reset.". 2. Press this button down with the tip of a ballpoint pen...
how to connect the linksys wap54g?
1. Power the wireless router off by pulling the power cord out of the rear control panel of the unit. 2. Power the modem off. To do so, pull the power cord out of the rear control ...
how to use a wap54g as a repeater?
1. Open your favorite browser. Enter “192.168.1.1” (without quotes) in the address bar and press the “Enter” button. This opens a login dialogue. 2. Type “admin” in both fields and...
how to set a wap54g to the client mode?
1. Type the following Internet Protocol (IP) address in the browser address bar: "192.168.1.245". Press "Enter.". 2. Type "admin" in the "User name" field of the security dialog bo...
how to restore the firmware for a wap54g?
1. Open your web browser and navigate to the Linksys support site to obtain the latest firmware for your device (see Resources.). 2. Download the firmware file to your desktop. 3. ...
how to bridge a linksys wap54g?
1. Connect the WAP54G to the PC using the Ethernet cable. 2. Open a web browser on your PC and type "192.168.1.245" in the address bar. 3. Enter the password "admin" at the prompt....
how to set up a linksys wap54g?
1. Place the Access Point near the center of the area you wish to include in your wireless network and set the antenna as high as possible. 2. Insert one end of an Ethernet cable i...
how to upgrade a linksys wap54g?
1. Write down a list of all the customized settings for your access point. You do not need to write down settings that have not been changed from default. 2. Download the firmware ...
how to troubleshoot a linksys wap54g?
1. Reboot your modem and Linksys router. Power both units down, then power on the modem, wait 45 seconds and then power on the Linksys. Reboot your computer and wait another 45 sec...
how to reset a linksys wap54g?
1. Straighten out the paper clip. 2. Locate the "Reset" button on the back of your router. It is on the left side of the back panel. 3. Press and hold the "Reset" button with the p...
how to reset a wap54g password?
1. Locate the "Cisco" logo on the front of the wireless router. 2. Press and hold the logo down for 10 seconds. The logo turns orange. 3. Release the button. The SSID and WPA-Perso...
how to connect a wap54g to a router?
1. Insert one end of the Ethernet cable into an open "LAN" port on your router. 2. Plug the other end of the Ethernet cable into the "LAN" port on the rear of the Linksys WAP54G. 3...
how to configure multiple wap54g?
1. Connect an Ethernet cable from the "Internet" port on the WAP54G to your modem. Connect a second Ethernet cable from one of the numbered ports to your computer's Ethernet port. ...
What is you new favorite WAP54G?
> I'll post screen grabs with the options circled to bypass router functions attached. Make-5-port-Switch.png 83 KB WAN functions disabled, port assigned to LAN switch instead
how to connect a wrt160n to a wap54g?
1. Plug the AC power cable into the circular port at the rear of the WRT160N and plug the other end into an available power outlet. 2. Plug the AC power cable into the circular por...
how to use the linksys wap54g as a wireless repeater?
1. Launch a web browser and access the router settings for the existing router on the network. To do so, enter 192.168.1.1 into the web browser and press enter on the keyboard. Ent...
how to connect a linksys wap54g to a wrt350n?
1. Plug the Linksys WAP54g directly into your computer. To do so, plug an Ethernet cable into the Local Area Network (LAN) port on the back of the router. Plug the other end of the...
how to install a wap54g to a motorola vt2442?
1. Plug the modem cable from the back of the Motorola VT2442 modem to a wall outlet. If you have a cable, use a coaxial cable. If you have DSL, use the phone line. 2. Plug the Ethe...
how to troubleshoot a set up of wap54g over the ethernet cable?
1. Connect a PC to the WAP54G by plugging one end of an Ethernet cable to the computer's Ethernet port. Connect the other end of the cable to the wireless access point using any of...
What is the DC requirements of the Linksys WAP54G version 3?
The WAP54G v3 needs much less current than it's brothers WRT54G(/S), abo...
What is the IP address for a Lynksys model wap54g?
The only way you can retrieve an IP address to enter it into your r...
Why Can't I Access WAP54G?
Try using a different web browser to hit the Admin page. I've had problems with firefox and certain admin pages before. If that doesn't work try pinging it to make sure you can eve...
How to increase the sensitivity on WAP54g v.2
With all the hacks you can do with a domestic range AP, you will only be able to slightly tweak it. You will never hack you $50 access point to be a $500 access point. Your best be...
How do I access linksys WAP54G to upgrade firmware?
You need to chage your IP to 192.168.1.50 (for example) http://www.hotcomm.com/FAQ/FAQ_staticIPXP.asp Using this link, and under the section 'Assign the IP address' following those...
How to determine the IP Address of a WAP54G while it's using DHCP?
You can find it by its mac address, which is on the bottom, if its not use this http://www.youngzsoft.net/cc-get-mac-address/ Whatever is the dhcp server should have the info you ...
why link led of WAP54G Linksys is not blink if i
First RESET your router to defaults settings.Press RESET button for 10 seconds it is in back side of router. Then connect your router to computer with ethernet cable then you can a...
how to set up psp internet with a wireless-g access point model wap54g?
1. Select the "Network Settings" icon on the far left of the PSP main menu. Select "Infrastructure Mode" from the next screen. 2. Select "New Connection" and "Scan" and your PSP wi...
Related Products FAQs
WAP54G WIRELESS
WAR FACTIONS
FinePix S1800
4 4GB
GAMES NINTENDO WII PRINCESS
PREMIUM IPOD
MSI LAPTOP
SEAGATE GO
LASER KEYBOARD
DELONGHI FRYER
BELKIN PRE-N
COMPACT III
MAXTOR III
About -  Privacy -   -  Careers -  Ask Answers  © 2013 Ask.com