YAMAHA VIRAGO FAQ

1. Take the seat off your Yamaha so you can access the fuel tank. Turn the fuel selector to "Off. Unscrew the bolt towards the rear of the tank, loosen the clamps and pull the fuel...
1. If the engine has stopped and will not start, check the fuel level. 2. If there is an adequate amount of fuel, then move on to check the compression system. 3. If there is not e...
1. Find the frame serial number. According to The Virago.co.uk, the frame serial number is located in two locations -- stamped on the right side of the frame while sitting on the m...
1. Fill the Virago's fuel tank with unleaded gasoline. 2. Open the fuel cap and pour the correct amount of fuel stabilizer into the tank. Refer to the label on the stabilizer bottl...
1. Install saddlebag brackets, if your motorcycle is not already equipped with them. Many people use saddlebags with out the brackets, but they are advisable to have, as these brac...
1. Raise the Virago using a motorcycle jack to get the front tire off of the ground. Remove the axle retaining nut from the axle using the Yamaha axle wrench. Hammer out the front ...
1. Make sure the gas tank is empty. 2. Remove the two screws holding the seat on the frame, pull the seat up and back and lift off the frame --- if the tank is an under-the-seat mo...
1. Lift your Virago's seat. Disconnect the spark plug wires. 2. Locate the oil pan drain plug on the bottom of your Virago's engine and remove it. Allow the oil to drain into your ...
1. Pull up the cushion at the front of the seat to access the bolts on both sides of the seat pan. 2. Unscrew both bolts from the seat pan with a 4-mm Allen wrench. Lift the front ...
1. Turn your motorcycle on and start the motor. Let the motor warm up by letting it run for a few minutes or by taking a short ride. Stop the motor once it has warmed up and lower ...
1. Purchase a pair of new mirrors from StarMotorcycles.com or another vendor. Make sure to locate mirrors that are fitted for your motorcycle. The stock mirrors on the Virago XV250...
1. Insert the ignition key into the seat release mechanism under the left side of the seat. Twist the key clockwise to unlock the seat. 2. Lift the rear of the seat upward to remov...
1. Mount the motorcycle on a service stand to hold it in an upright position. Lift the front wheel off the ground, using a jack. 2. Unscrew the speedometer cable from the speedomet...
1. Park the motorcycle on its kickstand and turn the ignition switch to the "OFF" position. 2. Grasp the left frame side cover. Gently work the cover's tabs out of the frame's rubb...
1. Check the fuel level in the Virago's fuel tank if the engine has stalled, lost power, or will not start. 2. Refill with unleaded gasoline if fuel the levels are inadequate. 3. I...
You should check your Yamaha Virago's motor oil every time you leave your driveway. Ensuring that the motor has a proper level of lubrication will prevent a considerable amount of ...
The 1983 Yamaha Virago is a cruiser style motorcycle. The front forks are the two large metal poles running from the handle bars down to the front tire. The front forks are what he...
89 MPG @ 50-55 mph rural winding (fairly flat, some hills) 89mpg (rider 6'2" 225 lbs). 76 MPG @ 65-75 mpg I-94 Jackson-Dexter MI commute.
1984 Yamaha Virago XV750 was one of the best selling motorcycles of that year. Thanks fo...
The Yamaha Virago 250 has the classic standard cruiser look without the unmanageable powe...
1. Bung. Remove the bung to let the oil out to drain. Remember to catch the oil in an oil drip tray (note the green tray in another photo) The bung is located on the left hand side...
1. Shift your motorcycle into "Neutral" and start the motor, allowing the oil to warm by letting the motor run for five to 10 minutes. Once the motor has warmed up to operating tem...
1. Lift the motorcycle onto its center stand, place it in neutral and start the motor. Let the motor run for five minutes to warm the oil, which will help it flow easier and speed ...
1. Unbolt the Yamaha exhaust mufflers from the exhaust pipes using the socket wrench. The mounting bolts are located just underneath the passenger foot peg with one additional moun...
As Yamaha's first V-twin-powered cruiser motorcycle, the Virago has become a favorite for riders who prefer the bike's classic lines and nimble handling. Although the Virago was av...
Living with Yamaha's Virago motorcycle can be relatively pain-free. With maintenance chores kept to a minimum, thanks to the Virago's reliable 750cc motor, the bike's owner can con...
1. Turn off the Virago's engine. 2. Lift off the seat cover and locate the fuse box. 3. Remove the cover of the fuse box to access the fuses. 4. Remove the turn signal relay from t...
1. Power on the Yamaha and let it run for a few minutes. The heat of the engine is going to help expand the metal of the baffles, which helps the removal process. You just need to ...
1. Secure the Virago so that it is standing upright with no danger of tipping over. 2. Inspect the inner tubes for any signs of scratches or other damage and for large amounts of o...
The valve clearance is: INTAKE 0.004in. (0.10 mm) EXHAUST 0.006IN. (0.15 mm) You must the rear cylinder at T for tdc and the front at I for tdc. Wheadjusting valves..
About -  Privacy -   -  Careers -  Ask Answers  © 2013 Ask.com