Question:How to Regrout a Brick Chimney
Not finding your answer? Try searching the web for
How to Regrout a Brick Chimney
Ask.com Answer for: How to Regrout a Brick Chimney
How to Regrout a Brick Chimney
Because brick chimneys are exposed to the elements, the brickwork deteriorates much quicker than that of a standard masonry wall. When the grout between the bricks cracks and crumbles away, it must be regrouted to restore the appearance of the chimney...
More »
Difficulty:
Challenging
Source:
www.ehow.com
Top Answers
1. Scrape out cracked grout from between the bricks of your chimney to the depths of the cracks using a grout rake. This inexpensive tool, which rolls along the surface of old grout and tears it up with a nail-like blade, may be found at any...
1. Remove the loose brick with a hammer and cold chisel. Chisel away as much of the old mortar as you can. 2. Use a soft-bristle brush to wipe away any remaining mortar on the brick and in the space where the brick was. 3. Fill a bucket with...
1. Use a ladder to access the brick chimney. 2. Use a pressure washer to clean the brick chimney. Wait two to three hours for the brick to dry. 3. Protect the roof below the chimney by covering it with fabric dropcloths. 4. Pour 2 gallons of...
More Web Answers
|
1. Remove the old brick by wiggling it out of place or by using a hammer and chisel if necessary. Angle a chisel at a low angle and tap the end of the chisel with a hammer to remove the old mortar completely. 2. Chip away old mortar from the...
http://www.ehow.com/how_7315920_replace-brick-chim...See entire page »
|
|
Installing flashing around your brick chimney is one way to prevent moisture from damaging other parts of your home. For the best water protection, you should also consider valley and step flashing. Keep your old flashing to use as a templat...
http://www.ehow.com/how_6740127_flash-brick-chimne...See entire page »
|
|
1. Put on protective goggles, a dust mask and work gloves. Wear rubber-soled shoes with excellent traction. 2. Lay down plywood sheets beside the chimney and inside the hearth, to protect the roof and hearth from dust, debris, falling mortar...
http://www.ehow.com/how_6607422_demolish-brick-chi...See entire page »
|
|
1. Thoroughly inspect the area around the chimney to make sure it is solid and safe. Roof areas around chimneys often have rotten decking, so make sure the roof can safely support your weight plus the weight of the bricks and debris that's r...
http://www.ehow.com/how_5561062_remove-brick-chimn...See entire page »
|
|
Bricks inside a fireplace are called refractory bricks, and they can withstand high temperatures. Refractory mortar bonds refractory bricks, and both materials can withstand temperatures exceeding 2,000 degrees Fahrenheit. The melting point ...
http://www.ehow.com/facts_8746545_there-brick-insi...See entire page »
|
|
1. Scrape away the loose mortar from the joints of the chimney with a screwdriver or masonry chisel. Count up the number of cracked bricks in the chimney (they need to be replaced) and remove all the cracked pieces of brick. 2. Grind away th...
http://www.ehow.com/how_6600320_rebuild-brick-chim...See entire page »
|
|
1. Remove any loose crumbs of mortar from the chimney using a hammer and chisel. If a brick is badly broken, remove it as well. Check to make sure the damaged areas do not go all the way back to the clay flue liner inside the chimney. 2. Mix...
http://www.ehow.com/how_7325156_repair-brick-chimn...See entire page »
|
|
1. Inspect the chimney for mortar joint cracks, splits or crumbling. Repair damage prior to sealing. Sealants with not effectively cover large gaps. Chip away damaged mortar with a masonry chisel and hammer. Replace the joint with new mortar...
http://www.ehow.com/how_7923116_seal-brick-chimney...See entire page »
|
|
The chimneys on many older homes often were not lined, exposing the bricks to direct contact with stove or fireplace emissions and the intense heat generated by a wood fire. Time also took its toll on these old chimneys, as the bricks absorb...
http://www.ehow.com/info_12175400_dead-brick-chimn...See entire page »
|
|
1. Lay a tarp, drop cloths or old towels around the indoor portion of the chimney to contain any mess from the cleaning process. 2. Wipe down the chimney bricks with a stiff, dry scrub brush to remove any surface debris. Then dip the same br...
http://www.ehow.com/how_4967925_clean-chimney-bric...See entire page »
|
|
1. Measure the amount of chimney that is exposed above the roof line. Cut two pieces of reinforcing bar twice the size of the exposed chimney, using the hacksaw. Cut two pieces of reinforcing bar to the size of the exposed chimney. 2. Insert...
http://www.ehow.com/how_7447232_reinforce-brick-ch...See entire page »
|
|
1. Set the tip of a carbide-tipped grout saw into a section of horizontal mortar. Remove the mortar to a depth of 3/4 of an inch. Move around the chimney, removing all the horizontal mortar from each side. 2. Place a 5-in-1 painter's tool in...
http://www.ehow.com/how_7350398_repoint-brick-chim...See entire page »
|
|
1. Measure the width of the inside of the chimney, using a tape measure. For a fireplace, it must be at least 8 inches wide. For a stove or heat furnace, the chimney width is at least 6 inches. 2. Measure the dimensions for the outside of th...
http://www.ehow.com/how_6617538_lay-brick-chimney....See entire page »
|
|
1. Mark the bricks you wish to cut out and remove. Use a marker to draw lines in the mortar, or joint lines between the bricks. This will help you keep your place and prevent you from cutting into the wrong area or cutting out more bricks th...
http://www.ehow.com/how_12019470_cut-brick-chimney...See entire page »
|
|
1. Pour dry mortar mix into a bucket or trough; add water and mix to a pastelike consistency. 2. Spray the bricks lightly with water. Use a spray bottle or garden hose with the nozzle set to mist. If the bricks are not damp, they will draw w...
http://www.ehow.com/how_7563066_mortar-brick-chimn...See entire page »
|
|
1. Chip out the cracked or crumbling mortar from the chimney joints, or the spaces between the bricks, with a hammer and chisel. Use firm, gentle taps rather than hard strikes to avoid damaging the bricks. Continue chipping off mortar until ...
http://www.ehow.com/how_7856578_fix-brick-chimney....See entire page »
|
|
1. Spray off surface dirt and dust, as well as visible algae, with a nozzle attached to a garden hose. This will remove much of the visible dirt on the chimney. If you perform this basic maintenance at least once per week, it will cut down o...
http://www.ehow.com/how_8390004_maintain-brick-chi...See entire page »
|