How to Install a Tile Roof?


You install tile roofing by first setting up the underlayment across the sheathing of the roof. Next, put in metal flashings wherever necessary. Proceed to nail two-inch thick cant strip with the roof’s eave. Allow 1/2-1 inch gap after every four feet for water to drain through the row of cant strip. Proceed to nail the batten below using the snapped line. Finally, put the tile down and work from left to right due to the vertical keyway that is in between the tiles.
Q&A Related to "How to Install a Tile Roof"
1. Install underlayment across the sheathing of the roof. There is a wide selection of asphalt-saturated felt underlayment available, but 30 pound felt is the most commonly used type
1. Lift the tile above the damaged one and prop it with a wooden wedge. Repeat this process with the adjacent tiles as well. Ad. 2. Grasp the broken tile with both hands and wiggle
The only thing that you are doing is putting down the rubber with some glue on top of a very clean and flat service. These instructions are very important. For more information, look
Tile is one of the oldest types of finish covering used on pitched roofs. Tile roofing has grown increasingly popular because of its fireproofing qualities. Clay or concrete tile
7 Additional Answers Answer for: how to install a tile roof
How to Install a Tile Roof
Tile is an excellent roof surface because it is waterproof and is able to withstand deep freezes and high winds. They can also be easily repaired because individual tiles, if they break or fall off, can be replaced with a minimum of fuss. A variety of... More »
Difficulty: Moderately Challenging
If you want to install Roof Tiles, here are some steps that need to be taken. First, install underlayment across the sheathing of the roof. There is a wide selection of asphalt-saturated felt underlayment available, but 30 pound felt is the most commonly used type. Research local building codes to determine what type of underlayment to use. Follow underlayment manufacturer instructions when installing. Install the metal flashing where needed. Places such as valleys, chimneys, skylights, and where a roof butts against a vertical wall will require metal flashing. The flashing should be a 28-ga corrosion-resistant metal. Nail the two-inch thick cant strip flush with the eave of the roof. This strip, which is twice the thickness of the battens, slants the first course of tiles so that it matches the rest of the courses. Every four feet, allow a half-inch to one-inch gap to let water drain across the row of cant strip and the battens, which will be placed across the entire roof.
When installing tile roofing, begin with setting up the underlayment all across the roof sheathing. Next, put up metal flashing wherever it may be needed. Proceed to nail the cant strip with the eave of the roof. For every four feet, make an allowance of ?-1? gap to let water drain away. Next, hook a tape measure to the eave of the roof to measure the length of the tile in use. Then measure the length of the roof and subtract one and mark the resultant length. Snap a line at both ends. Next, proceed to nail the batten below and flush with the snapped line. The battens will be nailed at the point where the lengths are 3? less the length of the snapped line. Finally lay the tiles by working from left to right. Rest the headlug behind every row of battens.
Roof tiles are to be installed with cement slurry with addition of water-proof compound. You should get the help of a technician since this work requires precision and tools.
Redoing your roof is a great way to save some money in this economy today. Although it will be a bit time consuming, it will be worth it to save the money. Click here for more help
The method for a tile roof installation varies based on the type of roof you start with. You can install the tiles with nails, screws, or lay the tiles in mortar on the roof. For more information look here: Installation Choices; Install a Concrete Tile Roof
Tile roofs are starting to become more popular. To install a tile roof you will need a saw, battens, cant strips, tiles, an underlayment and metal flashing. You can find more info at:
Explore this Topic
Tile is a material which is manufactured for covering roofs. It is made from materials such as glass, ceramic, stones or metals. To install Spanish roof you need ...
Hurricane straps solidify a new home's frame and roofing in the event of a hurricane. To install the hurricane straps to a roof, the process must be done during ...
There is one thing to remember when you install roof jacks and that is to make sure they are securely nailed into the rafters. The first step is to look at the ...
About -  Privacy -  Careers -  Ask Blog -  Mobile -  Help -  Feedback  -  Sitemap  © 2014