Topic: Delta Tub Shower 1400 Nickel
Not finding your answer? Try searching the web for Delta Tub Shower 1400 Nickel
Answers to Common Questions
How to Remove a Delta Shower Tub Strainer
Cleaning out a Delta drain system will require removing the strainer. The Delta shower tub strainer consists of a dome cover strainer and a drain plug. The dome cover is the surface piece you see that is most often referred to as the strain... Read More »
Source: http://www.ehow.com/how_6395948_remove-delta-shower-tub-strainer....
How to Repair a Leaky Delta 1400 Series Shower Faucet
Delta 1400 series faucets, like other faucets, leak from time to time. The faucet washers inside the cartridge valve assembly may wear out after continued use. When they do, leaks form because water finds it way around the worn gaskets. Thi... Read More »
Source: http://www.ehow.com/how_6664366_repair-1400-series-shower-faucet....
How is that removed? Delta Monitor Tub/Shower Faucet, Plumbing in...
Hi Don, The trim sleeve apears not to be screwed on so it should pull off. Then you will come to a spacer and a "O" ring, next is the bonnet. If it sticks use WD 40 on it. Do you have a exploded view of the valve and would you like one?... Read More »
Source: http://en.allexperts.com/q/1735/4193358.htm
More Common Questions
Answers to Other Common Questions
take handle off and adjust the nylon set ring it is to prevent kids from getting burned and is probably set wrong youll see teeth and a pointer just pull it out a little and turn it in the oppisite direction then push back in
Read More »
Source: http://www.fixya.com/support/t2186009-delta_tub_tap_only_cold_wat...
You don't have to turn the water off to replace this. There is no water going to the diverter unless your faucet is on. Just simply remove the handle and the round trim plate. The old diverter will screw out, add some pipe thread sealant to...
Read More »
Source: http://answers.yahoo.com/question/index?qid=20100215122153AA8HiNp
Sounds like your line had accumulated debris in it that let loose when the new mixing valve was installed. The cartridge is clogged and needs replaced. It should be exchanged for free by an authorized Delta wholesale distributor as a warran...
Read More »
Source: http://answers.yahoo.com/question/index?qid=20080410135618AAVZmg3
If you have a three knob showere valve then the problen's not in the spout. DO NOT remove the threaded male adapter on the end of the copper stubout, it's soldered on. It's there to connect to a front end threaded spout, (see image). Let me...
Read More »
Source: http://www.askmehelpdesk.com/plumbing/delta-tub-spout-leaks-when-...
Good question Jim, As you can see by the image I put up The copper stub out should be 1 1/2" min. And 2 7/8ths" max. Don't forget to sand off the burr on the end of the copper pipe or it will snag the "O" ring and roll it out of position. G...
Read More »
Source: http://www.askmehelpdesk.com/plumbing/delta-tub-shower-install-32...
First, you must turn the water off to the shower valve, which usually means shutting down the water to the whole house. Then take off the finish cover cap, and use an allen key or screwdriver to remove the set screw located on the side of t...
Read More »
Source: http://ashevilleplumber.com/delta-monitor-shower-faucet-repair/
Make sure to adjust the temperature before putting the handle on. Take the small o-ring off of the cartridge stem and remove the disc and rotate it counter clockwise to increase the temperature limit, or clockwise to reduce the temperature ...
Read More »
Source: http://ashevilleplumber.com/delta-monitor-shower-faucet-repair/
