Did you mean: On a Cisco Router Which Interface Should Be Used to Make the Initial Configuration?
Web Results

CCNA 1 Chapter 11 V4.0 Answers

ccnaanswers.com/ccna-1-chapter-11-v4-0-answers/

Apr 3, 2010 ... A technician applies the configuration in the exhibit to a clean router. .... On a Cisco router, which interface would be used to make the initial ...

Initial Configuration - Cisco

www.cisco.com/c/en/us/td/docs/routers/access/800/hardware/installation/guide/800HIG/initalconfig.html

Mar 28, 2016 ... For instructions on how to use Cisco Configuration Professional Express ... To create the initial configuration, the setup command facility ... You may also initially configure your router by using the Cisco IOS command-line interface (CLI) or by ... If your router does not have a default configuration file, go to the ...

Basic Router Configuration - Cisco

www.cisco.com/c/en/us/td/docs/routers/access/1900/software/configuration/guide/Software_Configuration/routconf.html

Mar 30, 2016 ... Use the show running-config command to view the initial .... 15, 20, 25, 30, 40, 50 Router(config)# memory-size iomem 25 Smart-init will be disabled .... To verify that you have properly configured the loopback interface, enter ...

Initial Configuration - Cisco

www.cisco.com/c/en/us/td/docs/routers/access/800/809/hardware/install/guide/809hwinst/initconfig.pdf

To create the initial configuration, , the setup command facility prompts you for basic ... Cisco IR809 Integrated Services Router Hardware Installation Guide. 4 ... To use the setup command facility, you must set up a console connection with the ... Any interface listed with OK? value "NO" does not have a valid configuration.

Cisco Device Initial Configuration Dialog | Free CCNA Workbook

www.freeccnaworkbook.com/workbooks/ccna/cisco-device-initial-configuration-dialog

So that annoying little prompt you get each time you boot a Cisco Router or ... This lab will discuss and demonstrate the Initial Configuration Dialog. ... However you'll never use this configuration dialog once you're experienced in navigating Cisco ... interface on the system Would you like to enter basic management setup ?

Basic Switch Configuration Guide with Examples

computernetworkingnotes.com/ccna-study-guide/basic-switch-configuration-guide-with-examples.html

We will configure a Cisco switch in packet tracer. ... Interface Configuration, Contain commands those modify the operation of an interface ... Setup, Used by router to create initial configuration, if running configuration is not present ...

Configuration Fundamentals Configuration Guide, Cisco IOS ...

www.cisco.com/c/en/us/td/docs/ios-xml/ios/fundamentals/configuration/15mt/fundamentals-15-mt-book/cf-setup.html

Perform this task to create an initial configuration for a ... Dialog does not allow you to ... router to the management ... interface name used to ...

Configure Cisco Router Step by Step Guide

computernetworkingnotes.com/ccna-study-guide/configure-cisco-router-step-by-step-guide.html

This basic router configuration tutorial provides step by step instruction for Cisco ... We need to perform some initial configurations on router before it can be used for routing. ... We have created this topology to give you a better overview of commands. You can use single router if you are unable to replicate this topology in ...

Initial Configuration of Cisco Switch and Router - Cisco Is Easy

ciscoiseasy.blogspot.com/2010/08/lesson-3-initial-configuration-of-cisco.html

Aug 9, 2010 ... Lesson 3 - Initial Configuration of Cisco Switch and Router ... Instead, you will get familiar with some useful commands we use very often ... Enable the interface facing the Internet Serial0/1 (we pretend it is the public interface).

CCNA Practical Studies | Configuring Point-to-Point Serial Interfaces ...

www.informit.com/library/content.aspx?b=CCNA_Practical_Studies&seqNum=42

To create a point-to-point connection between two routers, you can use other types of ... refer to Chapter 2 of Interconnecting Cisco Network Devices from Cisco Press. ... Example 7-26 walks you through these initial configuration steps. ... Now that you are in interface configuration mode for R5's Serial 0, you can execute the ...

More Info

On a Cisco router what interface is used to make the initial ...

www.answers.com

console port ... On a Cisco router what interface is used to make the initial configuration? ... Which port can be used for initial router configuration? aux. 2 people ...

Using the Command-Line Interface in Cisco IOS Software

www.cisco.com

Feb 24, 2010 ... After you have performed the initial configuration and connected the .... Inspect various states on the router, including the Cisco IOS state. ... to view the commands that you can use while the device is in ROM monitor mode.

Using the Command-Line Interface - Cisco

www.cisco.com

Oct 30, 2013 ... In order to have access to all commands, you must enter privileged EXEC ... You also can use global configuration mode to enter specific configuration modes. ... Router, unless it has been changed during initial configuration ...