Web Results
How to Set the Jumper on a Maxtor Hard Drive
If you are installing a second hard drive into your desktop computer, you need to know how to change the jumper settings on the back of the hard drive. Most hard drives have three jumper settings: Master, Slave and Cable Select. Which setting you... More »
Difficulty: Moderate
Source: www.ehow.com

Basic jumper settings for Maxtor ATA Hard Drives - Other World


Basic jumper settings for Maxtor ATA Hard Drives. Thank you for purchasing your new ATA hard drive from Other World Computing! Please review these jumper ...

Maxtor ATA Hard Drive Installation Guide (PDF) - Seagate


jumpers on additional hard drives attached to the built-in ATA ports must be set to ... manufacturer, or use the master/slave jumper settings instead. Figure 4.

Jumper Settings for Maxtor and Quantum® ATA hard drives. - Seagate


Interactive flash tutorial for properly placing jumpers on Maxtor and Quantum ATA /IDE drives.

Maxtor Jumper Settings - The Tech-FAQ


Sep 3, 2015 ... The hard drive's jumpers are the small, black pegs on the back of the ... is a Maxtor jumper setting that is the default for virtually all IDE drives.

Installation Of Maxtor Drives - Danny Piano Chesnut


Seagate Products, Maxtor®/Quantum Products. Jumper settings for Seagate ATA hard drives. Note: This figure depicts the jumper settings for recent Seagate ...

Maxtor and Quantum ATA Hard Drive Jumper Settings (Storage ...


May 22, 2006 ... Maxtor and Quantum ATA Hard Drive Jumper Settings (Storage) tutorial,tutorials, walk through, help, fixing, fix, fixes, support, repair, advice, ...

How to Set the Jumper on a Maxtor Hard Drive | Business ...


Review the user manual for your hard drive to determine the correct jumper settings, or check to see if the settings are printed on the hard drive itself.

How to Set a Maxtor Hard Drive to Slave (7 Steps) | eHow


Make certain the hard drive's jumper pin is set to "CS" or cable select. The jumper settings are determined by a small, removable tab found on the same end of ...

www.ask.com/youtube?q=Maxtor Hard Drive Jumper Settings&v=Ds1-JmbhGRM
Sep 28, 2008 ... Change the master/slave designation on a hard drive by using the cable select mode to modify the jumper settings. Adjust the master/slave ...
Popular Q&A
Q: Maxtor hard drive Jumper settings 52049h3 jumper settings.
A: The jumper settings may be printed on the hard drive's labeling, so check there.  If not, refer to page 2-5  of the PDF at. http://www.seagate.com/sta. ticfiles... Read More »
Source: www.experts-exchange.com
Q: How to Set the Jumper on a Maxtor Hard Drive.
A: 1. Remove the hard drive from your computer, being sure to disconnect both the power and data cables. 2. Decide which drive will be the Master and which drive w... Read More »
Source: www.ehow.com
Q: How do I change jumper settings on Maxtor hard drive, model:
A: Hello, Here's the manual for your drive. http://www.seagate.com/staticfiles/maxtor/en_us/documentation/manuals/dm_plus_40_ultra_ata_100_manual.pdf I think the s... Read More »
Source: www.fixya.com
Q: What are the jumper settings for Maxtor N256 hard drive?
A: http://www.seagate.com/staticfiles/images/support/en/us/mxo_ata_jumpers_rev.jpg this link should help you Read More »
Source: www.fixya.com
Q: How do you set a jumper pin to master on a maxtor hard drive?
A: A newer SATA drive shouldnt need to be set, but an older PATA drive can be set by adjusting the jumper pin on the drive, near the PATA connector. the actual set... Read More »
Source: answers.yahoo.com